SXBJ-12 Fitting Symmetrically Double Heads Plate Edge Milling Machine

A. The Nature and Specific Application of SXBJ-12 Special Made Sheet Metal Plate Edge Milling Machine:

1. Nature of the SXBJ-12 Special Made Sheet Metal Plate Edge Chamfering Machine:

1) The product name of this section implies on primary characteristic of the SXBJ-12 model equipment for plate edge chamfering to be introduced here: It has two sets of edge milling units, and installed in symmetrical position along both sides of the machine mechanical main body, for steel plate edge chamfering operation;

2) The small width strip plate to be edge beveled in SXBJ-12 special made machine for sheet metal plate end milling : (Fig.1)

2. Applicable Workpiece and Usage of SXBJ-12 Special Made Sheet Metal Plate Edge Chamfering Equipment:

1) Property: It is a Special Made Sheet Metal Plate Beveling Machine. The target workpieces to be processed are strip steel plates, which need to be edge milled for making welding groove on its both sides;

2) Applicable Workpieces: The prior equipment deployed before this special made machine of edge milling is CG4000 Strip Plate Cutting Machine, which cut steel plates into long slit strip plates of up to 12m length and 500~600mm width;

3) Applicating Example: One of the examples on the next equipment following the SXBJ-12 Edge Milling Machine is MP series Plate Butt Joint Welding Machine, which fabricates on the edge beveled strip plates edge chamfered from the SXBJ-12 model machine of edge milling, into semi-finished WIP (Working in Process) of larger steel plate, shown in below photo:

The flat butt joint steel plate which should be first edge grooved in SXBJ model Steel Plate Edge Milling Machine: (Fig.2)

4) Finished Workpieces: The chamfers/ Bevels/ Grooves made with the XBJ and SXBJ series machine for metal plate edge milling  are top edge and or straight edge chamfers/ Bevels of designated styles;

The upper and straight edges welding grooves that can be machined in XBJ model Sheet Metal Plate End Milling Machine: (Fig.3)

5) When should and how to make welding groove in the SXBJ-12 Special made Plate Beveling Machine?

a) Most of the times the workpieces do not need to have its bottom edges made into bevels, in the machine of sheet metal plate edge milling. This is basically workpieces steel plate with thickness 15mm and less;

b) If it is does necessary to carry out edge milling on bottom edges of workpieces steel plate, the workpiece need to be taken off from the machine of edge milling  first, and then turned over 180°, making its original bottom edge into top edge, and put onto the machine for sheet metal plate end milling again, to implement the second time operation of metal plate beveling.

B. Maintenance and Lubrication of the SXBJ-12 Special Made Sheet Metal Plate End Milling Machine:

1. Working Environment and Points of Attention on Daily Operation and Maintenance of the SXBJ-12 Special Made Sheet Metal Plate Edge Milling Machine:

1) As can be found from the attached picture and below photo, this set of 12m stroke special made machine for sheet metal plate edge milling  is installed outdoors under a canopy, rather than inside indoors workshop. It is a matter of expediency and restricted by on site resources;

2) Operating surroundings of the SXBJ-12 Special Made Sheet Metal Plate Edge Chamfering Machine: (Fig.4)

3) Edge Milling Machine working under such environment is more prone to grow aging due to direct intrusion of wind and rain. For this reason, special care should be taken on daily operation and service of the special made machine of sheet metal plate beveling  in such condition;

4) For this purpose, we provide detailed suggestion in the manual book of the XBJ and SXBJ series Edge Milling Machine for it’s the purpose of its proper maintenance. Customer can set up and implement strict TPM (Total Preventive Maintenance) plan and put it into practice based on practical condition;

2. Lubrication Plan and Implementation in the XBJ and SXBJ series Sheet Metal Plate Edge Milling Machine:

1) One of the main contents in maintenance of XBJ and SXBJ models machine of sheet metal plate edge chamfering  is lubrication, because such machine for edge milling  has all its critical working units in high speed revolving during the process of metal plate beveling, including its Milling Head/ Leadscrew nut Couple and Worm Gear Reducer, etc.;

2) For fulfilling on this task, we give detailed technical instruction on proper way of lubrication at the beginning of machine of edge milling put into work, and periodical lubrication in the long time use;

3) The Edge Milling Machine can maintain it’s the best status and the longest service time if these lubrication and maintenance to be carried out properly at customer site.

C. Technical Parameters of the SXBJ-12 Special Made Sheet Metal Plate Edge Milling Machine: